How to Reduce Machine Setup Time With Better Fixturing
The first time I put a stopwatch on one of our changeovers, I learned that if you want to reduce machine setup time, you have to look past the operator. I expected to find a slow operator. Instead, I found a slow system. A vertical machining center that cut parts for about eleven minutes per cycle sat idle for fifty two minutes while a skilled machinist swapped one job for the next.
To be clear, he wasn’t lazy and he wasn’t careless. He was walking to the crib for a parallel set, sweeping the fixed jaw of a vise with an indicator, tapping it with a dead blow hammer, and then sweeping it again. After that, he touched off a part, ran a first piece, and adjusted an offset by a few tenths. Every one of those steps made sense on its own. Together, however, they were eating almost a full hour of spindle time several times a week.
Why I Set Out to Reduce Machine Setup Time
Since then, I’ve spent most of my career on one question: how do you reduce machine setup time without asking people to simply hurry? After enough changeovers, enough fixture builds and enough mistakes of my own, the answer I keep coming back to is fixturing. In other words, not just buying fancier clamps, but designing how parts are located, how fixtures meet the machine, and how much of the work happens while the spindle is still turning.
This article walks through the approach I use on the shop floor. Admittedly, some of it costs money. Still, a surprising amount of it costs almost nothing.
Before You Reduce Machine Setup Time, Find Where It Goes
Before you spend a dollar on workholding, first find out where your minutes are going. When I break down a typical milling changeover, the time usually falls into five buckets:
- Searching and gathering. First, there’s finding the right fixture, the right bolts, the right jaws, the right tools, the print and the program.
- Mounting and aligning. Next comes bolting the fixture or vise down, then indicating it square and parallel to the machine axes.
- Establishing offsets. After that, the operator touches off or probes to set the work coordinate system.
- Tooling changes. Then the operator loads tools, measures them, and enters their lengths and diameters.
- First article and adjustment. Finally, the operator runs a part, inspects it, tweaks offsets, and runs another part.
A Real Changeover, Broken Down
For example, in the fifty two minute changeover I mentioned, the machinist spent roughly fourteen minutes searching, eleven on indicating, nine on tooling, and twelve on first article and adjustment. Meanwhile, the rest went to cleaning chips out of the table and fixture. In fact, only the cutting tool work was truly tied to the machine. Nearly everything else was either avoidable or could have happened before the machine stopped.
That breakdown, therefore, is the real starting point. Fixturing directly attacks the second, third and fifth buckets. In addition, it indirectly shrinks the first one when you organize it properly.
Use SMED Thinking to Reduce Machine Setup Time
The most useful mental model for setup reduction is still the one developed decades ago in the stamping world. Essentially, the core idea of SMED is to shift as many changeover steps as possible into work done while the equipment keeps running, and then simplify whatever must still happen with the machine stopped. The method came out of Japanese industry, and most sources credit Shigeo Shingo, who developed it in the 1950s at the Toyo Kogyo factory that later became Mazda.
What “Single Minute” Actually Means
Interestingly, people often get hung up on the name. The “single minute” actually means a single digit number of minutes. So the target is anything under ten, not literally sixty seconds.
Internal Versus External Work
Here’s why this matters for fixturing. Shingo split every changeover into two kinds of work:
Internal setup is anything that can only happen while the machine is stopped. For instance, swapping the fixture on the table is internal.
External setup, on the other hand, is anything that can happen while the previous job is still running. Loading parts into a spare fixture, presetting tools, staging bolts and printing the traveler are all external.
Consequently, a good fixturing strategy does two things. First, it moves work from internal to external. Second, it makes the remaining internal work so repeatable that it barely needs checking. However, if you buy a quick change system but your operator still waits for the old job to finish before he walks to the crib, you’ve simply bought expensive hardware and kept the old habit. In my view, that’s the most common reason shops fail to reduce machine setup time even after a big workholding purchase.
Locate First, Clamp Second to Reduce Machine Setup Time
Most slow setups trace back to a fixture that clamps well but locates poorly. In that case, the part is held tight, but nobody trusts where it is. As a result, someone indicates it, probes it, or runs a test cut.
The foundation of good locating is the classic six point method. Specifically, three locators sit on the primary datum, two on the secondary and one on the tertiary, which together remove all six degrees of freedom. When a fixture follows that logic, the part can only sit one way. Moreover, it sits there every time.
Match Datums and Avoid Overconstraint
There are a few rules I hold myself to when I design or review a fixture. To begin with, match the fixture datums to the drawing datums. If the print calls out a bore and a face as primary and secondary, then locate off that bore and that face. When your fixture reference matches the designer’s reference, the parts you cut tend to measure the way inspection expects. Therefore, you stop chasing offsets.
Equally important, don’t overconstrain. More locators feel safer, but in reality they fight each other. In fact, one fixture design guide notes that using more than six locating contacts can loosen repeat accuracy from about 0.02 mm to somewhere between 0.04 and 0.08 mm. Similarly, I’ve seen the same thing on castings with a fourth pad on the bottom: the part rocks, and the operator learns to “feel” it into place. That feel, unfortunately, is setup time.
Clamp Toward the Locators
Beyond that, push the part into the locators. Clamp force should drive the part toward the locating surfaces, never away from them or sideways across them. Otherwise, if a clamp lifts the part off a pad, your locating scheme is only a suggestion.
Also, spread locators apart. The wider the span between your two secondary locators, the less angular error a tiny chip or burr can create.
Lastly, use a round pin and a diamond pin. When locating off two holes, one full round pin and one relieved diamond pin give you accurate location without binding. Granted, it’s an old trick, but it’s still one of the best.
Ultimately, when the locating is right, the operator loads the part, clamps it and runs. In short, no indicator comes out of the drawer.
Build One Interface to Reduce Machine Setup Time
This is where most shops get their biggest single gain. Typically, the slowest part of mounting a fixture or vise is the alignment: sweeping it in, bumping it, and then sweeping again. The fix, then, is to stop aligning fixtures to the machine every time. Instead, give every fixture the same precise connection to the table.
How Zero Point Clamping Helps Reduce Machine Setup Time
Today, zero point clamping is the most common way to do this. A receiver plate stays permanently on the table, and every vise, subplate or fixture carries pull studs that drop into it. At the heart of these systems is a mechanical link between a receiver, often called a clamping pot, set into a base or grid plate, and a retention stud fastened to the workholding sitting above it.
As a result, the payoff is repeatability you can rely on without checking. Mate, for example, states that its zero point bases repeat within 0.0002 inch, or 0.005 mm. At that level, you can pull a fixture, run three other jobs and put it back without indicating. That’s because the interface defines the fixture’s location, not whoever bolted it down.
A Realistic Look at the 90 Percent Claim
You’ll often see manufacturers claim reductions of up to 90 percent in fixturing setup time. Roemheld, for instance, describes cutting setup time by as much as 90 percent and links that directly to no longer needing to indicate. Personally, I treat that number as a best case.
In my experience, the realistic gain on the mounting and aligning portion is very large. Nevertheless, your total changeover will still include tooling, offsets and first article. On that fifty two minute changeover, for example, a zero point base took the eleven minutes of indicating down to under a minute. That was a huge win; however, it didn’t fix the fourteen minutes of searching. In other words, hardware solves hardware problems.
Tips Before You Buy a Zero Point System
If you’re going this route, there are a few practical notes to keep in mind:
- Standardize stud spacing across the shop. First, pick one pattern and stick with it so every fixture fits every machine that carries a receiver. Otherwise, mixed patterns quietly bring back the old problem.
- Protect the interface. Chips in a receiver will ruin repeatability. So, use covers when stations are empty and blow out pots before seating anything.
- Use it beyond the mill. Additionally, some shops extend the same zero point reference into inspection and CMM fixturing. That way, a part checked on the CMM sits exactly the way it sat on the machine. The same logic carries over to welding cells on the fabrication floor.
- Older machines can benefit too. Notably, you don’t need a new machining center to adopt this. A receiver plate bolted to the table of an older mill gives it the same quick change behavior.
The Budget Alternative
If zero point hardware isn’t in the budget yet, you can still get much of the benefit with a precision subplate. Simply give it two dowel holes and build fixtures that locate on those dowels. Admittedly, it isn’t as fast as a zero point system. Even so, it eliminates sweeping, and that’s the most expensive part of the mount.
Fixture Plates and Subplates That Reduce Machine Setup Time
A well made fixture plate is one of the most underrated tools in a job shop. Think of it, in essence, as a permanent, flat, accurate surface with a known grid of tapped holes and dowel holes, mounted once and left on the machine.
When I design these, I generally follow a simple pattern:
- Dowel holes on a known grid. Every fixture that goes onto the plate locates on two dowels, one round and one slotted or diamond. As a result, it drops into the same position every time.
- Tapped holes on a matching grid. Likewise, clamps and fixtures bolt down to a consistent pattern, so operators aren’t hunting for a T slot nut that fits.
- Stored offsets for each position. Once you know where the dowels are relative to machine zero, you also know where every fixture sits. Therefore, store those offsets and stop touching off.
- Clear labeling. Finally, engrave the plate’s coordinate positions right onto its surface. It sounds trivial; nonetheless, it saves a lot of guessing.
For families of similar parts, furthermore, a single fixture plate with interchangeable nests can replace a dozen dedicated fixtures. Since each nest locates on the same dowel pattern, changing from one part number to another is simply a matter of lifting one nest out and dropping another in.
Quick Change Jaws and Chucks Reduce Machine Setup Time on the Lathe
Turning, of course, has its own setup drains: changing chuck jaws, boring soft jaws, and swapping between a chuck, a collet system and a mandrel. Fortunately, quick change chucks and jaw systems attack those directly.
A Turning Shop Example
One of my favorite case studies on this comes from a turning shop profiled in Modern Machine Shop. Before quick change chucks, each setup there cost roughly half an hour of production time. Afterward, jaw changes took under two minutes and complete setups averaged about five minutes. In addition, the same article makes a point I’ve seen proven many times: the better quick change chucks are repeatable enough that shops can often skip reboring a saved set of soft jaws on repeat jobs.
That second benefit, though, is easy to overlook. If you bore a set of soft jaws for a repeat part, mark them, and store them with the job, then the next run starts with jaws that already fit. Thus, you’ve just turned a twenty minute internal task into a two minute one.
More Quick Change Ideas for Turning
Beyond chucks, there are other quick change ideas worth considering:
- Collet systems with quick change heads work well, for example, for bar work and smaller diameters.
- Quick change face drivers and mandrels can share an interface with your chuck. Consequently, swapping between them doesn’t mean pulling the whole chuck.
- Dedicated machines for stock ranges also help. If you have enough lathes, keeping certain machines on certain stock sizes reduces how often jaws and bar feeds need to change at all.
Error Proof Fixtures to Reduce Machine Setup Time
Obviously, a fast setup that produces a bad first part isn’t fast. For that reason, error proofing, sometimes called poka yoke, belongs in every fixture design.
The easiest tactic, by far, is asymmetry. If a part can physically fit into a fixture backward or upside down, then sooner or later someone will load it that way. So offset one locating pin, add a blocking pin where a feature should be, or shape the nest so the wrong orientation simply won’t sit flat.
Small Details That Pay Off
In addition, other details pay off quickly:
- Color code fixtures and their matching components so that jaws, bolts and nests travel together.
- Engrave the part number, program number and fixture offset directly on the fixture body, too.
- Add part present sensing on higher volume fixtures. That way, the machine won’t cycle if a part isn’t seated against its locators.
- Use captive hardware. Similarly, clamps with captive screws and swing clamps that stay attached to the fixture mean no loose parts to lose on the floor or in the chip conveyor.
Altogether, every one of these cuts down the first article and adjustment bucket, which, in my experience, is the one shops underestimate most.
Make Offsets Permanent to Reduce Machine Setup Time
Once your fixtures locate repeatably to the machine and your parts locate repeatably to the fixtures, you can finally stop rediscovering offsets every time.
How I Set It Up
Here’s how I set it up. To start, assign every fixture a permanent work offset and record it in the setup sheet. If fixture 14 always sits at a known position on the receiver, then its offset doesn’t change.
Next, use a quick probing routine as a check, not a search. Instead of finding the part from scratch, the probe confirms the part is where you expect it to be, within a tolerance. If it’s out, the machine alarms. If it’s in, however, the program runs.
Then, keep tool data in the machine and in the tool crib. Tools assigned to a family of jobs should stay in the magazine where possible. Meanwhile, measure tools that come and go on a presetter before they reach the machine.
Fixturing and Presetting Work Together
That last point, in particular, goes hand in hand with fixturing. Modern Machine Shop notes that setting tools by hand at the machine is a frequent source of wasted time and errors, whereas measuring them offline on a presetter lets the machine keep running. In that sense, better fixturing and offline tool presetting are partners. One fixes where the part is, while the other fixes where the cutting edge is. Used together, they reduce machine setup time far more than either one alone.
Stage Everything Outside the Machine to Reduce Machine Setup Time
This is where SMED becomes physical. The goal, put simply, is that when the machine stops, everything the operator needs should already be within arm’s reach.
Here’s what works for us:
- Setup carts for each job or job family. The cart holds the fixture or nest, the hardware, the soft jaws, the preset tools, the gauges and the setup sheet. Then, when the current job is nearly done, the next cart rolls up beside the machine.
- Duplicate fixtures for high runners. If a job runs often, an operator can load and check a second fixture at the bench while the first one is still on the machine. As a result, the change is literally lifting one off and dropping the other on.
- Shadow boards near each machine hold wrenches, hex keys and torque tools sized for that machine’s workholding, so nobody needs to fetch anything.
- Torque values marked on the fixture. After all, operators shouldn’t guess at clamping torque, and inconsistent torque is a quiet cause of inconsistent parts.
Notably, none of this needs expensive equipment. Rather, it needs discipline and somebody who owns the setup process. In fact, staging is often the cheapest way to reduce machine setup time in any shop.
Reduce the Number of Setups, Not Just Their Length
Of course, the fastest setup is the one you don’t have to do. Indeed, a lot of setup time hides in jobs that take three or four operations when they could take one or two.
Here are some fixturing approaches that consolidate operations:
- Multipart fixtures. Holding several parts at once means more spindle time per load and, therefore, fewer loads per batch.
- Tombstones on horizontals. Likewise, four faces, many parts, one load.
- Five axis workholding. A five axis machine can often finish in one setup a part that once required four or five. Moreover, because the datums never move, accuracy usually improves too. Pair that with a low profile vise or a dovetail fixture on a riser, and you get the tool access you need without extra handling.
- Op one, op two on the same plate. Finally, put both operation fixtures on the same subplate so one load sequence finishes a part every cycle.
In the end, each eliminated setup removes all five buckets at once, not just one of them.
Measure Your Progress as You Reduce Machine Setup Time
Simply put, you can’t improve what you don’t watch. In fact, some of the biggest gains I’ve helped shops find came from filming a changeover and watching it as a team. Naturally, nobody likes seeing themselves walk to the crib four times, but the video doesn’t argue.
A Routine That Sticks
With that in mind, here’s the routine I recommend:
- Time a baseline. First, record a full changeover from last good part to first good part. That definition matters, because setup isn’t over when the program starts; it’s over when a good part comes off.
- Sort every step into internal or external. Then, for each internal step, ask whether it truly needs the machine stopped.
- Fix the biggest bucket first. For example, if searching is fourteen minutes, a setup cart will help more than a zero point system right now.
- Write standard work. Once you’ve found the fast way, document it with photos so every operator does it the same way. After all, setup times that vary wildly between people usually mean the process lives in people’s heads instead of on paper.
- Track it over time. Lastly, a simple chart of changeover times per machine, posted where everyone can see it, keeps the improvement from fading.
Where Better Fixturing Won’t Save You
Honestly, I’d be doing you a disservice if I pretended fixturing fixes everything. In particular, it won’t help much if:
- Your programs aren’t proven. If every new job needs a dozen edits at the machine, then the problem is in programming and simulation, not workholding.
- Your raw material varies. Likewise, saw cut blanks that vary by a quarter inch will fight any fixture. So standardize your stock prep.
- Your tooling isn’t controlled. Even a perfect fixture with mystery tool lengths still produces scrap.
- Your scheduling fights you. Similarly, if jobs bounce between machines randomly, fixtures can’t stay where they work best.
In short, fixturing is the backbone of setup reduction. Even so, it works best as part of a system that includes programming, tool management and scheduling.
A Simple Plan to Reduce Machine Setup Time
If you’re wondering where to begin, this is the sequence I usually follow with a shop:
- Week one: First, time and film three typical changeovers on your busiest machine. Then sort steps into internal and external.
- Month one: Next, build setup carts and shadow boards, and move gathering and tool prep outside the machine. In many cases, this alone cuts a quarter or more off the changeover.
- Month two: After that, fix locating on your highest running fixtures. Add dowels, correct overconstrained designs, and add error proofing.
- Month three: Then install a common fixture interface on one machine, either a zero point system or a doweled subplate, and assign permanent offsets.
- Ongoing: Finally, roll what works to the next machine, consolidate operations where you can, and keep tracking the numbers.
What Happened to That Fifty Two Minute Changeover
So what happened to that fifty two minute changeover I started with? After a setup cart, a doweled subplate, a corrected nest design, permanent offsets and preset tools, it settled around eleven minutes. Later, we added a zero point base and got it under eight. Importantly, no one was rushing. Instead, the system was simply better.
Final Thoughts
If you want to reduce machine setup time, stop thinking of setup as something operators do. Instead, start thinking of it as something engineers design. The fixture decides how a part is located. Meanwhile, the interface decides how a fixture meets the machine, and the cart decides what’s ready when the spindle stops. Get those three right, and as a result, your best machinist’s speed becomes everyone’s speed.
After all, setup time is capacity you already paid for. Better fixturing is how you get it back, and it’s the most reliable way I know to reduce machine setup time for good.
Frequently Asked Questions
What is the fastest way to reduce machine setup time?
First, separate internal work, which needs the machine stopped, from external work, which can happen while it runs. Then move as much as possible outside the machine. The Lean Production guide to SMED lays out this process clearly.
Is zero point workholding worth the cost for a small shop?
For high mix work with frequent changeovers, usually yes, because it removes repeated indicating and offset setting. In fact, Modern Machine Shop’s article on zero point workholding explains how it supports pulling setups off and returning them without losing location.
How accurate are zero point clamping systems?
Generally, quality systems repeat to around 0.005 mm. For typical figures, see Mate’s overview of zero point workholding and LANG Technik’s zero point guide.
What does the 3, 2, 1 locating principle mean in fixture design?
Essentially, it uses three locators on the primary datum, two on the secondary and one on the tertiary to control all six degrees of freedom of a part. Machally’s guide to 3, 2, 1 locating also covers datums, clamping sequence and overconstraint.
What does “single minute” mean in SMED?
It means a changeover completed in a single digit number of minutes, under ten, rather than literally one minute. The Kaizen Institute’s SMED explanation covers this, along with the related one touch concept.
Can quick change chucks help on CNC lathes?
Yes. Quick change chucks shorten jaw changes and, in addition, let shops reuse saved soft jaws on repeat jobs. Modern Machine Shop’s “Quick Change Turns Time Into Money” shows a real shop example.
References
- “SMED (Single Minute Exchange of Die).” Lean Production
- “SMED Explained: What Is Single Minute Exchange of Dies?” Six Sigma Development Solutions
- “SMED Explained: Reduce Changeover Time and Boost Efficiency.” Kaizen Institute
- “What Is SMED? Single Minute Exchange of Die Explained.” RZ Software
- “Zero Point Workholding: Faster Changeovers, Repeatable Results.” Modern Machine Shop
- “Quick Change Turns Time Into Money.” Modern Machine Shop
- “Turn Your Operational Gaps Into Efficiency Gains.” Modern Machine Shop
- “Zero Point Workholding: More Than Machining Operations.” Mate Precision Technologies
- “Zero Point Clamping.” Roemheld USA
- “Boosting CNC Efficiency With Zero Point Clamping Systems.” LANG Technik USA
- “Keep Machines Running With Modular Workholders.” Cutting Tool Engineering
- “CNC Fixture 3, 2, 1 Locating Principle: Datum Strategy, Clamping Sequence and Deflection Control.” Machally
- “Fewer Setups, More Profit: The Hidden Power of Efficiency in Modern Machining.” North South Machinery
- “Single Minute Exchange of Die.” Wikipedia
